A lettuce crop can look fine for two weeks, then stall, pale out, or turn rough at the leaf edges. Most of the time, the problem is not that lettuce needs a complicated program. It needs a complete base feed, a stable root zone, and measured corrections when the plant gives you a reason to make one.
This lettuce nutrient example starts with the growing medium, because soil, coco, and hydroponics do not hold nutrients the same way. Feed a mild, complete base nutrient first. Then use the meter and single-mineral additives to correct calcium, magnesium, or micronutrient issues without throwing off the whole reservoir.
The lettuce nutrient example starts with the medium
Lettuce grows quickly and has a shallow root system. That means it reacts quickly when the root zone gets too dry, too concentrated, or out of pH range. A pale plant is not automatically underfed. In a small hydro reservoir, it may be a pH problem. In coco, it may be calcium or magnesium availability. In soil, it may be too much water around the roots.
For seedlings and fresh transplants, start light. Lettuce does not need a heavy feed to establish. Raise strength as plants build a full root system and begin stacking leaves. Watch new growth, not just the oldest leaves. New leaves tell you whether the current feed is supplying what the plant can use now.
A practical target range for most lettuce is pH 5.8 to 6.2 in hydroponics and coco. Soil-grown lettuce generally works well with irrigation water and root-zone conditions closer to pH 6.0 to 6.5. For EC, young lettuce commonly runs best on the low end of a nutrient program, while larger heads can take a moderate feed. Water quality, cultivar, temperature, light level, and reservoir size all affect the right number.
Use the directions on the base nutrient label as the starting rate. Check EC after mixing, then adjust gradually. Do not chase a single EC target if the plant is growing evenly, holding a healthy leaf color, and drinking at a normal pace.
Build the feed in the order lettuce uses it
Start roots before pushing foliage
At germination and transplant, use Bionova Roots with your normal light base feed. Roots is for the early stage when lettuce needs to settle into soil, coco, rockwool, or a hydroponic channel. A well-established root system makes the rest of the nutrient program easier to manage.
For a countertop hydro garden or a tray of butterhead starts under an LED, keep the reservoir clean and avoid letting EC climb as water evaporates. Top off with plain water when needed, then recheck the EC before deciding whether more nutrient belongs in the tank.
Choose the base nutrient for the root zone
In potting soil, raised-bed containers, or other soil-based mixes, use Bionova Soil Supermix. It is the base feed for growers who want a complete nutrient profile without trying to assemble a different bottle for every basic feeding. Mix it into water according to the label, apply to already-moist media, and avoid saturating the pot every time you feed.
In coco, use Bionova Coco Forte A+B. Coco does not behave like soil. It holds water well but has limited nutritional buffering, so the root zone needs a regular and balanced nutrient supply. Mix Part A into the water completely before adding Part B. Never combine concentrates together in a measuring cup or bottle.
For deep-water culture, nutrient film technique, vertical towers, ebb-and-flow systems, and recirculating lettuce tables, use Bionova Nutri Forte A+B Hydro. This is the base feed for a water-based root zone. Add Part A to the reservoir, mix thoroughly, then add Part B and mix again. Measure EC and pH only after the solution is fully blended.
That order matters. A complete base nutrient supplies the broad nutrition. Additives are for a specific correction, not a substitute for a base feed.
Add silica early if your water and system call for it
Bionova SiLution is a mono-silicic acid product used early in the mixing process. If you run it, add it to plain water before your base nutrients, then mix well. It fits growers who want silicon in a form that is easy to use in a feed program.
Lettuce does not need a pile of additives. Keep the program simple. SiLution is a deliberate addition, not a reason to raise EC beyond what the crop and environment can support.
Correct the deficiency you actually see
A lettuce plant with brown leaf margins may be dealing with calcium movement, but the cause can be low calcium in the feed, unstable moisture, high room heat, or rapid growth under strong light. Adding more bottles without checking the environment can make the reservoir less balanced.
When you need to raise calcium in the nutrient program, use Bionova Ca 15. Ca 15 is for a targeted calcium adjustment. Use it when your water source, crop response, or feed plan calls for more calcium than the base nutrient is providing. Keep an eye on total EC after adding it.
If older leaves show interveinal yellowing while veins stay greener, magnesium may be the missing piece. Bionova MgO 10 lets you address magnesium specifically instead of changing the entire base recipe. In coco, this can be especially useful when the feed and water source do not match the crop’s needs.
For new growth that comes in pale or uneven while the base feed, pH, and EC are already in range, Bionova Micromix is the targeted option for micronutrients. Use it with a reason. If pH has drifted out of range, fix pH first. A micronutrient bottle cannot solve nutrient lockout caused by the wrong root-zone pH.
PK 13-14 is not part of a normal lettuce program. Lettuce is a leaf crop, not a fruiting crop, so pushing phosphorus and potassium with a bloom additive is usually the wrong move. Put your attention into the base feed, calcium balance, root-zone moisture, light, and temperature.
Measure before you adjust
A grower can make a clean nutrient mix and still run into problems if the pH and EC are unknown. The HM Digital HydroMaster HM-200 pH/TDS/EC/Temp Meter gives you the numbers that matter in one handheld tool: pH, EC, TDS, and water temperature.
Check source water before mixing. Then check the finished nutrient solution. In recirculating hydro, check the reservoir daily or often enough to catch drift before it becomes a plant problem. If EC rises while the water level falls, the plants are taking up more water than nutrients. Top off with water and reassess. If EC falls quickly, the crop may be using nutrients faster than water, but do not react to one reading alone. Look at the trend over several checks.
For soil and coco, test the feed going in every time you mix. Runoff readings can help experienced growers diagnose a container, but runoff is a snapshot, not a command to make a large correction. Change one variable at a time and give lettuce a few days to respond.
Keep your lettuce feed simple enough that you can explain every bottle in the reservoir. Start with the correct Bionova base nutrient, measure pH and EC, and use Ca 15, MgO 10, or Micromix only when the crop and numbers point in that direction. Start with the HM Digital HydroMaster HM-200 pH/TDS/EC/Temp Meter before changing the feed.
Shop: bdubbgrowsllc.com

